Unistrut Fall Protection has expanded its product line to include a portable monorail system to meet high demand for mobile on-site fall arrest systems. The new product is ideal for use in air and truck transportation and also works well for transportation equipment manufacturers.
What should not be used as an anchorage point?
Never connect more than one employee to a lanyard. Knots shall not be used for an anchorage point. Double locking snap hooks shall always be used. Inspect the snap hook to ensure it fully closes and locks.
Can you use a crane hook as an anchor point for fall protection?
Unlike the Construction Industry, there is no provision in the General Industry Code that permits or describes the use of a crane hook as an anchor point for a personal fall arrest system.
How much does a fall protection anchorage point need to be rated for?
There are two paths to OSHA compliance when it comes to fall protection anchorage: OSHA 1910.140(c) (13)(i) states that anchors “shall be… capable of supporting at least 5,000 pounds (22.2 kN) per employee attached.”
What is the best system to use for fall protection?
Guardrails
Guardrails. Guardrails should be your first choice when it comes to preventing falls. They provide workers with the best protection because, when erected properly, they actually eliminate the fall hazard. With guardrails in place, workers can’t fall because there is no open edge.
What is the minimum safe working load for an anchorage point?
“Anchorages to which personal fall arrest equipment is attached shall be capable of supporting at least 5,000 pounds (22.2 kN) per employee attached, or shall be designed, installed, and used as part of a complete personal fall arrest system which maintains a safety factor of at least two, under the supervision of a …
Can you use an overhead crane for fall protection?
Although a mobile scissor lift, aerial work platform or crane walkway can provide access to the crane components, fall protection must still always be used when working at heights. Depending on the operation, the type of overhead crane used, and the work that must be performed, a variety of solutions may be utilized.
What equipment is needed to protect you from falling in high places?
This could include body belts or saddles, descent devices, full-body harnesses, energy absorbers or lanyards, and personal fall arrest systems (PFAS). These guidelines should be used to be sure that the protective equipment is properly used and maintained: 1.
Can you tie-off to a forklift for fall protection?
Section 1926.453(b)(2)(v) of the Aerial Lift standard provides that workers in aerial lifts and boom-type platforms must be tied-off. Workers on scissor lifts must either be tied-off or protected by guardrails.
What can be used as an anchor point for fall protection?
When choosing an anchor point, strongest first is a good rule of thumb. A steel member is preferable. Wood may be acceptable as a temporary anchor but must be engineer-certified. Anchor bolts should be inspected by a qualified person, as should through-bolts and plate washers.
Which of the following should not be used as an anchorage point?
What can be used as an anchor point?
Speaking of beams, structural steel is a great option when looking for an anchor point (not decorative steel or roof joists, necessarily, but good, strong, load-bearing steel beams). If your work is fairly static in location, you can get a beam clamp and if you need to travel, you can get a beam trolley.
Can a vehicle be used as an anchor point for fall protection?
Access systems provide purpose-built fall protection anchor points that can surround equipment that requires work at height, such as rail cars, aircraft or vehicles, often consisting of a ladder access system, jib or mobile frame.
What is the best method of fall protection?
The preferred solution to all fall hazards is elimination. The reason for exposure to the fall hazard is challenged and evaluated to determine if a change in the procedure, practice, location or equipment will eliminate exposure to the fall hazard.
What’s the difference between spring and nut in Unistrut?
The only difference between the two is that the spring holds the channel nut in a more precise location, which is useful for applications when you are working with channel that is suspended overhead. Take your channel and insert the nut anywhere along the continuous slotted channel.
How to make Unistrut connections in Five Easy Steps?
How to Make Unistrut Connections in Five Easy Steps Take your channel and insert the nut anywhere along the continuous slotted channel. The rounded nut ends make it easy to insert into the channel. The nut pictured features a spring, but any Unistrut nut will work.
What do you need to know about Unistrut framing system?
Unistrut is an incredibly versatile framing system for completing projects with ease. If you are new to the Unistrut framing system and need a few pointers on how Unistrut works, we have just the post for you.
What are the reduction factors for Unistrut beam loads?
Beam loads are based on a simple span and assumed to be adequately laterally braced. Unbraced spans can reduce beam load carrying capacity. Refer to Page 62 of the Unistrut Engineering Catalog for reduction factors for unbraced lengths. 3. For pierced channel, multiply beam loads by the following factor:
